Magic Platform Bed Frame

Natural, untreated spruce, pine or fir.
Alternating 4" and 6" wide slats spaced 2 inches apart, for maximum support and breathability.
3 cross-support rails for stability.
Centre legs and centre support rail for Full/Double, Queen, King and California King
The frame height is measured from floor to the top of the slats.
Clearance from the sides is the frame height minus 4.25 inches
Clearance from the ends - head or foot - is the frame height minus 5.75 inches.
Standard 12", or custom heights available
The Magic Bed Frame can be made with a custom incline or decline of 3" - 5.5" elevation at the head or foot upon request. This may be helpful for acid reflux and sleep apnea symptoms, however, please talk with your doctor to ensure an incline or decline is right for you.
Untreated natural wood will naturally age and will darken over time. If you choose to - you can stain this frame and lacquer can be applied.
If you are in our delivery area (Vancouver Island or Lower Mainland) we will typically assemble the frame for you. If this frame is shipped to you - a #2 Robertson (square) screwdriver is required, preferable electric.

Natural, untreated spruce, pine or fir, no special care needed.

Twin: 38 x 75 inches
Twin XL: 38 x 80 inches
Full/Double: 54 x 75 inches
Full/Double XL: 54 x 80 inches
Queen: 60 x 80 inches
King: 76 x 80 inches
California King: 72 x 84 inches
Custom size*: please let us know the required dimensions

Standard height: 12 inches (from the floor to the top of the slats)
Clearance from the sides: The frame height minus 4.25 inches
Clearance from the ends - head or foot: The frame height minus 5.75 inches.

Custom sizing available upon request
*Custom fee may apply.

While it is possible to assemble this bed frame with a manual screwdriver, it will be much easier if you use an electric or cordless screwdriver. You will need a square #2 Robertson bit - which is usually red.

The Magic Platform Bed Frame has 10 numbered parts indicated with a pencil number on each part. To assemble, please follow the sequence of the numbered parts.

1) Find pieces #1 and #2 (legs)
2) Find #3 and #4 (side rails)
3) Lay them on top of the legs - matching the coloured dots (colour dot on the side rail to match the same colour dot on the legs).
4) Position the leg between the outside pencil lines on the rails.
5) Tighten the screws on all four corners, while ensuring that the rail sits flush against the leg.
6) Find #5 (centre leg)
7) Slide #5 under the rails and position it between the outside pencil lines on the rails.
8) Tighten the screws on #5, and ensure that the rail sits flush against the leg. You may need to press down on the rail and squeeze it against the leg while screwing it in.
9) Find #6 (centre rail). Twin and Twin XL frames do not include this piece.
10) Lay the centre rail across the centre of the legs - and line up with the pencil lines on the legs and on the rail.
11) Tighten the 3 screws
12) Find #7 and #8 (rounded end slats).
13) Position them so that the rounded corners are on the outside corners of the bed and that the arrows are just covered by the slat.
14) Use the screws provided to attach (3 screws for each slat set is usually enough - use black pilot holes).
15) Find #9 and #10 (middle slats).
16) Position so the arrows are just covered by the slats (the distance between the slats is about 2 inches).
17) Visually check that the slats are spaced equally and that they line all up.
18) Attach the middle slats (3 screws for each set of slats is usually enough, use black pilot holes)

We have included a few extra screws in case they are needed.

Please contact us if you have any questions or require assistance.
250–597–7378, ext 2 or info@resthousesleep.com